Drag S3 Pod Voopoo
Age verification
More details on this product
DRAG S3 POD VOOPOO
Orientated towards a vape in indirect inhaling (MTL), the Drag S3 pod offers a vape in semi-direct pull, energetic. Included with the cartridge with the MTL PnP X drip tip, the Drag S3 pod remains compatible with the PnP X coils by Voopoo. The strong points of the pod is the autonomy in 3000 mAh with an interesting compact for vaping everywhere.
This third version of the Drag S pod is modern with a chipset which handles several modes of vape which are simple to use, Smart, RBA and ECO. The pod offers you personalise the screen with several themes and animations in a few clicks. Voopoo innovates with a very practical Everest Lab switch. This capacitive button reacts to the touch of a finger to activate the pod. The Drag S3 locks as soon as the finger is no longer in contact, securing the operation of the pod. This switch avoids damaging the pod and the coil with any accidental presses.
The Drag S3 is included with the PnP X 0.6Ω (18 - 23 watts and ≈ 50% in VG) and the PnP X 0.8 Ω (12 - 16 watts and ≤ 50 % in VG). The cartridge is compatible with the PnP X coils in 0.15 Ω to 1.0 Ω. It is also compatible with the PnP X DTL. The Drag S3 has a maximum output power of 60 watts. The integrated battery in 3000 mAh has a recharge capacity of 5V/2A.
To whom does the Drag S3 de Voopoo address ?
The Drag S3 pod addresses vapers who are in search of polyvalence to pass to a MTL to RDL vape without difficulties and has a maximum output power of 60 watts. A strong point of the pod and its compatibility with all the PnP X products. It also addresses vapers in indirect inhaling in search of a compact electronic cigarette which has good autonomy both in battery and e-liquid
Drag S3 and Everest Lab switch
It contains a 3000 mAh battery but remains compact. The Drag S3 conserves the practical format with a size which allows it to be vaped everywhere. With an armor in zinc alloys , a coating in PU leather around the handle. A coating which has different engravings depending on the colour. The pod has 2 setting buttons, TFT coloured screen (0.96-inch) which benefits for the first time a switch signed Everest Lab. A capacitive switch that locks the pod when it is not in contact with the hand.
One pod, three modes
There are three modes available with the Drag S3 depending on your needs. The Smart mode will be activated to be sure that the coil does not get damaged with a high power. The RBA mod allows you to use the power in watts from 5 to 60 watts as desired. Finally the Eco mode can be used to economise the battery for longer. The Drag S3 pod also has the possibilities to be personalised with the TFT coloured screen with several themes and animations.
3000 mAh
The Drag S3 pod offers a maximum power of 60 watts with an integrated battery which has a capacity of 3000 mAh. The battery can be recharged in USB-C with the cable included and has a capacity of 5V/2A. It is recommended to use a charger adapted to this capacity.
PnP X MTL
With the top aeration, the PnP X MTL cartridge preserves the pod from accidental leaking of e liquid. The aeration is adjustable to choose the pull, tight or open. The cartridges can hold up to 5 ml in e liquid with a filling front the side. The cartridge is compatible with all the PnP X coils.
Filling of the Drag S3 :
- Remove the PnP X cartridge PnP X from the pod
- Delicately remove the cap from the base of the cartridge
- Fill the reservoir
- Close the reservoir and install the cartridge to the pod
PnP X coils
All the PnP X coils are compatible with the Drag S3 pod. With coils between 0.15 Ω to 1.0 Ω, sold separately depending on your preference. The coils have 4 joints to guarantee the perfect sealing. There are 2 coils included with the Drag S3.
- PnP X 0.6 Ω for a vape in RDL and MTL. With a power between 18 and 23 watts and e liquids with 50% in VG or less is advised.
- Pnp X 0.8 Ω for a vape in MTL. With a power between 12 and 16 watts and e liquids with a maximum of 50 % in VG is advised.
Filling of the Drag S3 Pod :
- The PnP X cartridge must be empty
- Remove the cartridge from the Drag S3
- Remove the coil from the cartridge
- Insert the new coil into the reservoir
- Wait at least 15 minutes after adding the e liquid
Features of the Drag S3 Pod Voopoo :
| Dimensions | 124.25 x 28 x 33 mm | Autonomy | 3000 mAh |
|---|---|---|---|
| Range of coils | 0.1 Ω - 3.0 Ω | Power | 5 w - 60 w |
| Charging capacity | 5V/2A | Capacity | 5 ml |
The Drag S3 Pod is made by Voopoo.
The Drag S3 Pod is included with:
- 1 Drag S3 Pod
- 1 PnP X MTL cartridge
- 1 PnP X 0.6 Ω coil
- 1 PnP X 0.8 Ω coil
- 1 510 drip tip
- 1 USB-C cable
- 1 User notice
Discover the Packaging of the Drag S3 Pod Voopoo
Opinions of users
Avis soumis à un contrôle
?
- Pour plus d’informations sur les caractéristiques du contrôle des avis et la possibilité de contacter l’auteur de l’avis, merci de consulter nos CGU
- Aucune contrepartie n’a été fournie en échange des avis
- Les avis sont publiés et conservés pendant une durée de cinq ans
- Les avis ne sont pas modifiables : si un client souhaite modifier son avis, il doit contacter Avis Vérifiés afin de supprimer l’avis existant, et en publier un nouveau
- Les motifs de suppression des avis sont disponibles ici
- J. Jonathan
- le 25/09/2026
-
5/5
- S. Patricia
- le 23/09/2026
-
5/5
- V. Piet
- le 15/09/2026
-
5/5
- B. Remy
- le 19/08/2026
-
5/5
- B. Jose
- le 14/08/2026
-
5/5
- M. Laetitia
- le 09/07/2026
-
5/5
- D. Olivier
- le 09/07/2026
-
5/5
- B. Isabelle
- le 16/06/2026
-
5/5
- C. Cindy
- le 06/05/2026
-
4/5
- B. Pascal
- le 19/04/2026
-
5/5
Customer questions / answers
Do you wish to ask a question ?
One of our experts of customers will answer you
Le Petit Vapoteur
Age verification
